| Title | Char from the co-pyrolysis of Eucalyptus wood and low-density polyethylene for use as high-quality fuel: Influence of process parameters |
|---|---|
| ID_Doc | 15248 |
| Authors | Samal, B; Vanapalli, KR; Dubey, BK; Bhattacharya, J; Chandra, S; Medha, I |
| Title | Char from the co-pyrolysis of Eucalyptus wood and low-density polyethylene for use as high-quality fuel: Influence of process parameters |
| Year | 2021 |
| Published | |
| Abstract | Providing a valuable application to the under-utilized solid residue of co-pyrolysis of biomass and plastics could substantially improve economic and environmental sustainability of the process, thereby fostering circular economy. This study focuses on the variation of thermal and physiochemical characteristics of solid char, produced from the co-pyrolysis of waste low-density polyethylene (WLDPE) and Eucalyptus wood with varying pyrolysis temperatures from 300 to 550 degrees C, residence times of 90-150 min, and relative percentage of 33% and 25% (w/w) WLDPE in the feedstock. The highest values of yield (37%), energy density (1.25) and high heat value (31 MJ/Kg) were observed with the char produced at 300 degrees C. The physical inhibition caused by the overlaying plastic coating on the surface of the char below 450 degrees C resulted in the same. However, with the increase in temperature, increase in fuel ratio by 78-79% and fixed carbon content by 68-69% were observed. The highest concentrations of fixed carbon (39%), fuel ratio (0.81) along with the lowest O/C and H/C ratios (0.07 and 0.13) were observed with the chars produced above 450 degrees C depicting their high degree of carbonization. The fuel value indices of all the chars were > 500 GJ/m3 indicating their suitability as high-quality fuels. Significant influences of residence time and feedstock ratio were also observed on properties of the char. The analysis of variance and principal component analysis also depicted significant variations in the properties of the char produced below and above the temperatures of 450 degrees C due to the inhibitory and synergetic effects. While the chars produced at 300-350 degrees C could be used for combustion/co-combustion in coal-fired boilers, chars produced above 450 degrees C can be opted as household fuel due to their low losses of energy, water vapour, and smoke during combustion. (c) 2021 Elsevier B.V. All rights reserved. |
Similar Articles
| ID | Score | Article |
|---|---|---|
24053
|
Cupertino, GFM; da Silva, AM; Pereira, AKS; Delatorre, FM; Ucella-Filho, JGM; de Souza, EC; Profeti, D; Profeti, LPR; Oliveira, MP; Saloni, D; Luque, R; Dias, AF Jr Co-pyrolysis of biomass and polyethylene terephthalate (PET) as an alternative for energy production from waste valorization(2024) | |
| 15106
|
Seraj, S; Azargohar, R; Dalai, AK Hydrothermal carbonization of sawmill shavings for fuel pellet production: A robust strategy for sustainable energy(2023) | |
| 15479
|
Vanapalli, KR; Bhattacharya, J; Samal, B; Chandra, S; Medha, I; Dubey, BK Optimized production of single-use plastic-Eucalyptus wood char composite for application in soil(2021) | |
| 12829
|
Ahmad, J; Vakalis, S; Patuzzi, F; Baratieri, M Effect of process conditions on the surface properties of biomass chars produced by means of pyrolysis and CO2gasification(2021)Energy & Environment, 32.0, 8 | |
| 8816
|
Swiechowski, K; Sygula, E; Koziel, JA; Stepien, P; Kugler, S; Manczarski, P; Bialowiec, A Low-Temperature Pyrolysis of Municipal Solid Waste Components and Refuse-Derived Fuel-Process Efficiency and Fuel Properties of Carbonized Solid Fuel(2020)Data, 5.0, 2 | |
| 15010
|
Januszewicz, K; Hunicz, J; Kazimierski, P; Rybak, A; Suchocki, T; Duda, K; Mikulski, M An experimental assessment on a diesel engine powered by blends of waste-plastic-derived pyrolysis oil with diesel(2023) | |
| 10366
|
Racek, J; Chorazy, T; Miino, MC; Vrsanská, M; Brtnicky, M; Mravcová, L; Kucerík, J; Hlavínek, P Biochar production from the pyrolysis of food waste: Characterization and implications for its use(2024) | |
| 23865
|
Armanu, EG; Secula, MS; Tofanica, BM; Volf, I The Impact of Biomass Composition Variability on the Char Features and Yields Resulted through Thermochemical Processes(2024)Polymers, 16, 16 | |
| 26791
|
Cuevas, AB; Leiva-Candia, DE; Dorado, MP An Overview of Pyrolysis as Waste Treatment to Produce Eco-Energy(2024)Energies, 17, 12 | |
| 15997
|
Sormo, E; Silvani, L; Thune, G; Gerber, H; Schmidt, HP; Smebye, AB; Cornelissen, G Waste timber pyrolysis in a medium-scale unit: Emission budgets and biochar quality(2020) |